In the article about the Sonoff SNZB-03 motion detector I had already described how you can use a motion detector to monitor your own SmartHome to automate further. Not only lights can be switched on and off automatically. A (simple) alarm system can also be implemented in this way.
Another alternative to the Sonoff SNZB-03 motion detector is the Ikea TRADFRI motion detector. This is a little cheaper (currently 10 euros) and fairly readily available through the provider Ikea.
What you have to do to get this in your Node Red Integrating an instance to react to movements is described in the following article.
Safety instructions
I know the following notes are always kind of annoying and seem unnecessary. Unfortunately, many people who knew "better" have lost eyes, fingers or other things due to carelessness or injured themselves. Data loss is almost negligible in comparison, but even these can be really annoying. Therefore, please take five minutes to read the safety instructions. Because even the coolest project is not worth injury or other trouble.
https://www.nerdiy.de/sicherheitshinweise/
Affiliate links/advertising links
The links to online shops listed here are so-called affiliate links. If you click on such an affiliate link and make a purchase via this link, Nerdiy.de will receive a commission from the relevant online shop or provider. The price does not change for you. If you make your purchases via these links, you support Nerdiy.de in being able to offer other useful projects in the future. 🙂
Requirements
Helpful articles:
Before you start this article, you should have prepared a Raspberry Pi so that it can be reached via the network and controlled via SSH. Of course, zigbee2mqtt and Node Red should also be installed and configured.
- RaspberryPi – setup for nerdiys!
- RaspberryPi – The first configuration!
- RaspberryPi – Control the RaspberryPi via SSH
- NodeRed – Installing NodeRed on the RaspberryPi
- Zigbee - Installing zigbee2mqtt on the Raspberry Pi
- Zigbee - register devices, sensors and actuators with zigbee2mqtt
In the following lists you will find all the parts you need to implement this article.
Required tool:
| Number | Link |
|---|---|
| 1x | Screwdriver set Buy at Amazon |
| 1x | SD card reader Buy at Amazon |
Required material:
Enable Zigbee2mqtt Dashboard
In my opinion, the easiest way to add new devices to your Zigbee network is to use the zigbee2mqtt dashboard. In case you haven't activated this yet, you will find helpful hints in the article Zigbee - Administration of Zigbee2mqtt via the dashboard.
Register motion detectors with zigbee2mqtt
Before you can evaluate the Ikea TRADFRI motion detector using Node Red, you must first integrate it into your Zigbee network.
I have a little more detail on how to integrate devices into your own Zigbee network in the article Zigbee – register devices or sensors and actuators with zigbee2mqtt described. The following two steps summarize this briefly.
To put the Ikea TRADFRI motion detector into pairing mode, you have to insert the batteries and the button on the back
- Briefly press 4x in a row
The LED in the motion detector should then flash and the button should connect to your Zigbee network shortly afterwards.
You can track the status of the connection process in the zigbee2mqtt log.
Log into the NodeRed configuration interface
Before you can edit your NodeRed configuration, you must - if activated - first log into the NodeRed configuration interface.
Import node code
The dashboard node should already be installed and configured so that you can also control your Zigbee device via the Node Red dashboard or display the values. You can find information about this in the following article.
If you are also over Pushbullet If you want to be automatically reminded of a dead battery in your Zigbee button, you should also have the Pushbullet Node installed. You can find information about this in the following article.
As an alternative you can of course also pushover or E-mail use as a notification. You can find information about this in the following articles.
After that, all you have to do is import the NodeCode linked below into your NodeRed environment. Information on how to import Node Red code can be found in the article NodeRed - import and export node code .
As always, you can find the Node Red code in the Nerdiy Git repository under the following link:
Of course you still have to adapt the code to your button. In order for this to work correctly, you have to enter the IEEE address or the “friendly name” of your button in the Node Red code.
To do this, open the properties of the selected node and enter your IEEE address in the selected area under "Payload...". How to find out the IEEE address of your Zigbee device is described in the article Zigbee – register devices or sensors and actuators with zigbee2mqtt described.
In order for the update function to work via the Node Red Dashboard, you must also enter the address here in the marked area.
At the point marked here you can also adjust the message that is sent as soon as the charge level of the button's battery falls below 20%.
In this example, I have also included three options that you can use to be informed when the battery level is empty.
Of course, you can simply delete the ones you don't need. 🙂
You can of course also use the newly registered Zigbee device via the zigbee2mqtt Dashboard control or read out.
In the following category I have also listed other Zigbee devices which can be controlled or read out with the Node Red code offered there.
More articles on the topic
I have summarized other articles on the subject of Zigbee and zigbee2mqtt in the following category. There you will also find articles on various Zigbee devices and how they look like Node Red can be controlled.
External links:
- https://www.zigbee2mqtt.io/devices/E1525_E1745.html#ikea-e1525-e1745
- https://www.zigbee2mqtt.io/supported-devices/
Have fun with the project
I hope everything worked as described for you. If not or you have questions or suggestions please let me know in the comments. I will then add this to the article if necessary.
Ideas for new projects are always welcome. 🙂
PS Many of these projects - especially the hardware projects - cost a lot of time and money. Of course I do this because I enjoy it, but if you think it's cool that I share the information with you, I would be happy about a small donation to the coffee fund. 🙂
English 
Deutsch 
Français 
Español 
Nederlands