Description
The PrintAirPipe - 125 Actuator & Sensor Set contains all currently available actuator and sensor segments of the PrintAirPipe Systems. The segments included are listed below.
Are you looking for other offers for the PrintAirPipe system?
There are also the following segments:
- PrinAirPipe - Complete set
- PrinAirPipe - ServoValve
- PrintAirPipe - AirSensor Segment
- PrintAirPipe - AirFlowSensor segment
- PrintAirPipe - 360° intake segment
Air Sensor Segment
With the help of the PrintAirPipe - 125 Air Sensor Segment for the PrintAirPipe System it is possible to measure various properties of the air around the pipe system.
For this purpose, a BME680, a BME280 and one of the available Fermion gas sensors from DF-Robot be installed.
The sensors can then be read out using the SeeedStudio XIAO ESP32 S3 built into the sensor segment. Thanks to the firmware based on the ESPHome framework, the data can easily be forwarded to a SmartHome system or elsewhere and processed accordingly.
This also makes it possible to react to certain values. For example, the supply air path can be shut off after a certain change in air quality has been detected. For this purpose, the PrintAirPipe - ServoValve be used.
Servo valve segment
The PrintAirPipe servo valve can be used to block or regulate the air flow in the PrintAirPipe system pipe run. This is practical if, for example, you want to shut off a supply air or exhaust air path.
The control is realized via an MG90 servo and an ESP32 board. Both are installed on the pipe segment and supplied with power via a USB-C connection. The firmware of the ESp32 is based on ESPHome and can therefore be easily integrated into Home Assistant or other SmartHome systems.
The valve can then be closed, opened or even partially opened or closed from the SmartHome system.
The valve status can also be switched between open and closed directly on the unit using a touch switch installed on the unit. The current status of the valve is displayed via an LED on the unit.
360° Intake Segment
With the PrintAirPipe - 360° Intake Segment, it is possible to direct the air inside the PrintAirPipe pipe system to the outside or to draw air from the outside into the inside of the pipe system.
The ventilation openings in the segment can be closed or opened either manually using a small lever or automatically.
The firmware of the control electronics is based on ESPHome and can therefore be integrated into many SmartHome systems such as HomeAssistant.
AirFlowSensor segment
The PrintAirPipe - 125 AirFlowSensor Segment can be used to measure the volume of air moved or the speed of the air in the pipe system.
The electronics are based on an ESP32 S3, three LEDs and a Hall sensor. The entire electronics can be supplied with power via a USB-C cable. The rotational speed of the propeller inside is shown in an animation on the outside. (Further information in the video linked below)
Please note: No physical components will be sent. You will receive the files in STL format and must print them out on a 3D printer in order to build the project.
This offer contains the STL files you need to print the 3D printable components for the PrintAirPipe Actuator & Sensor Set required.
- You will soon find further information on the assembly and other components required in the assembly article. It will be linked here as soon as it is published.
- Observe the safety instructions linked below during assembly and use: Click here
Additional components are required to build the complete project. A complete list of the required parts can be found here
Required tool:
| Number | Link |
|---|---|
| 1x | Screwdriver set Buy at Amazon |
| 1x | Soldering iron Buy at Amazon |
Material required for the servo valve segment:
Material required for the Air Sensor Segment:
360° Intake Segment
AirFlowSensor segment
Gallery
Servo valve segment
Air Sensor Segment
360° Intake Segment
AirFlowSensor segment
3D printing information
- Filament type: e.g: PLA
- Layer thickness: 0.2mm
- Infill: 15%
- Wall lines: 2
ESPHome example configuration
You can find an example configuration for ESPHome under the following link:
- Servo valve segment: https://github.com/Nerdiyde/ESPHomeSnippets/blob/main/Snippets/PrintAirPipe/servo_valve/servo_valve.yaml
- Air Sensor Segment: https://github.com/Nerdiyde/ESPHomeSnippets/blob/main/Snippets/PrintAirPipe/airSensor/PrintAirPipe_airSensor.yaml
- 360° Intake Segment:
https://github.com/Nerdiyde/ESPHomeSnippets/blob/main/Snippets/PrintAirPipe/360deg_intake/printairpipe-360intake-ctrlr-dev1.yaml - AirFlowSensor segment:
https://github.com/Nerdiyde/ESPHomeSnippets/blob/main/Snippets/PrintAirPipe/airFlowSensor/printairpipe-airflowsensor-segment.yaml
Videos
Dimensions
The following is an overview of the usual dimensions of the various pipe segments. If dimensions are missing, please use the contact form let us know and we will add this later.
Servo valve segment
Air Sensor Segment
360° Intake Segment
AirFlowSensor segment
File list
Servo valve segment
- PrintAirPipe_servo_valve_blade_rotation_lever_X.stl
- PrintAirPipe_servo_valve_blade_servo_connection_lever_X.stl
- PrintAirPipe_servo_valve_blade_X.stl
- PrintAirPipe_servo_valve_body_X.stl
- PrintAirPipe_servo_valve_body_wall_mount_X.stl
- PrintAirPipe_servo_valve_mechanic_cover_X.stl
- PrintAirPipe_servo_valve_mechanic_side_cover_assembly_X.step
- PrintAirPipe_servo_valve_mechanic_side_cover_wemos_fix_X.stl
- PrintAirPipe_servo_valve_servo_elevation_lever_X.stl
Air Sensor Segment
- PrintAirPipe_125mm_air_sensor_segment_insert_X.stl
- PrintAirPipe_125mm_co_sensor_segment_insert_lid_X.stl
- PrintAirPipe_125mm_sensor_segment_mcu_clamp_V1.0.stl
- PrintAirPipe_125mm_sensor_segment_V1.0.stl
360° Intake Segment
- 360degree_inatek_electronics_housing_lid_X.stl
- 360degreen_intake_segment_mcu_clamp_X.stl
- electronics_housing_assembly_X.stp
- PrintAirPipe_125mm_360degree_intake_segment_200mm_insert_connection_rod_X.stl
- PrintAirPipe_125mm_360degree_intake_segment_200mm_insert_lever_manual_X.stl
- PrintAirPipe_125mm_360degree_intake_segment_200mm_insert_lever_X.stl
- PrintAirPipe_125mm_360degree_intake_segment_200mm_insert_X.stl
- PrintAirPipe_125mm_360degree_intake_segment_200mm_X.stl
- servo_connection_lever_360degree_intake_X.stl
- servo_elevation_lever_360degree_intake_X.stl
AirFlowSensor segment
- mcu_clamp_X.stl
- PrintAirPipe_125mm_AirFlowSensor_electronics_housing_assembly_X.step
- PrintAirPipe_125mm_AirFlowSensor_segment_electronics_lid_X.stl
- PrintAirPipe_125mm_AirFlowSensor_segment_propeller_X.stl
- PrintAirPipe_125mm_AirFlowSensor_segment_screw_plug_X.stl
- PrintAirPipe_125mm_AirFlowSensor_segment_X.stl
English 
Deutsch 
Français 
Español 
Nederlands
Reviews
There are no reviews yet.