The FRITZ!Box is not only a very good router for the home network. Equipped with the right Smart Home accessories, it can also become the Smart Home center of your house […]
Weiterlesen
Tag: SmartHome
HowTo: Tasmota - Switch on socket delayed with switch on delay
In order to be absolutely sure that I have really switched off all devices (soldering iron, etc.) after leaving my workplace/desk, I have been switching off the consumers at my desk for years […]
Weiterlesen
HowTo: Zigbee - IKEA STYRBAR push button E2001/E2002 via zigbee2mqtt into NodeRed
The IKEA STYRBAR button is slightly larger than the little brother of the Ikea TRADFRI E1743 button. But it also offers a few more functions and - due to the two [...]
Weiterlesen
HowTo: Zigbee - Integrate Xiaomi Aqara MCCGQ11LM door/window sensor into NodeRed via zigbee2mqtt
In the article on the Sonoff SNZB-03 motion detector and Ikea TRADFRI motion detector, I mentioned before that a smart home can also be expanded into a (limited) alarm system. You can […]
Weiterlesen
HowTo: Zigbee - Integrate Ikea TRADFRI motion detector E1525/E1745 via zigbee2mqtt in Node Red
In the article about the Sonoff SNZB-03 motion detector, I already described how you can use a motion detector to further automate your own SmartHome. Not only lights […]
Weiterlesen
HowTo: Zigbee - read 4x wall switches TuYa TS0044 using Node Red
In a large part of my smart home I use the Ikea TRADFRI E1743 buttons. These can be used to conveniently switch up to four devices on and off. Recently I […]
Weiterlesen
HowTo: Node Red - Read out the temperature of the FRITZ! DECT Repeater 100
The FRITZ! I recently bought a DECT repeater to improve the range of my DECT phones. Unfortunately, my Fritz Box has to be in the basement, because […]
Weiterlesen
HowTo: Fritz Box - Find out the AIN of your SmartHome device
SmartHome devices that are compatible with the FRITZ!Box are addressed via an AIN. This AIN is a unique identification number that is assigned to the respective device. For example, if you use […]
Weiterlesen
HowTo: Zigbee - IKEA TRADFRI shortcut button E1812 via zigbee2mqtt into Node Red
The IKEA TRADFRI shortcut button E1812 is the little brother of the Ikea TRADFRI E1743 button. Both are identical in size. The only differences with the shortcut button are that this […]
Weiterlesen
HowTo: Zigbee - Integrate TuYa room temperature and humidity sensor TS0201 into Node Red via zigbee2mqtt
I stumbled across the TuYa TS0201 temperature and humidity sensor while looking for a simple humidity sensor. Actually, I was looking for a simple humidity sensor with a display […]
Weiterlesen
HowTo: Node Red - Sending push messages using Pushover from NodeRed
So far I have used the Pushbullet Node for notifications from my SmartHome. Unfortunately, the Pushbullet app - i.e. the counterpart on your smartphone with which you receive the messages [...]
Weiterlesen
HowTo: Raspberry Pi - Get Linux system information with Neofetch
If you ever find yourself in the situation of having to quickly collect the most important system information about your Raspberry Pi or another Linux system, Neofetch is a very helpful tool. With […]
Weiterlesen
HowTo: NodeRed - Automatic freeze alert via pushbullet, pushover or email
For a while I've owned one of those car covers that you put over the car to prevent ice from forming on the windows in cold temperatures. This cover […]
Weiterlesen
HowTo: Zigbee - Sonoff SNZB-03 motion detector via zigbee2mqtt into NodeRed
I think a smart home is always really practical when it relieves work or makes life more pleasant. Admittedly, the possibilities are not huge in this regard. But who ever […]
Weiterlesen
HowTo: Zigbee - Integrate Ikea TRADFRI E1743 push button via zigbee2mqtt in NodeRed
The IKEA TRADFRI button E1743 is one of the most used buttons in my SmartHome. It is very cheap at (currently) 6 euros per piece and at the same time the quality is very good […]
Weiterlesen
HowTo: Zigbee - Register devices or sensors and actuators to zigbee2mqtt
In order for you to be able to use Zigbee devices for your SmartHome, they must of course first be connected to your Zigbee network. This can be implemented in different ways. The easiest way new devices […]
Weiterlesen
HowTo: Zigbee - Prepare a Sonoff zigbee 3.0 USB Dongle Plus for zigbee2mqtt
To be able to use Zigbee sensors or actuators to control your SmartHome with zigbee2mqtt you need a Zigbee adapter. This is the interface between Zigbee device and SmartHome system (e.g. NodeRed) and [...]
Weiterlesen
HowTo: Zigbee - Migrate a CC2530/CC2531 coordinator under zigbee2mqtt to another coordinator
I've been using zigbee2mqtt for quite a while to integrate Zigbee sensors and actuators into my SmartHome. For a few years I have had one on the CC2530 or CC2531 IC […]
Weiterlesen
HowTo: Zigbee - Administration of Zigbee2mqtt via Dashboard
Zigbee2mqtt could initially only be configured and controlled via the configuration file or access to the MQTT server. Meanwhile, however, there is a very useful extension for zigbee2mqtt that makes it possible [...]
Weiterlesen
HowTo: Zigbee - Installation of zigbee2mqtt on the Raspberry Pi
Recently I started to convert parts of my SmartHome to the Zigbee standard. In the past, I still used sensors and actuators based on the simple 433Mhz radio. [...]
Weiterlesen
HowTo: ESPEasy - Set time synchronization with the DS3231 / DS3232 RTC
Thanks to NTP server ESPEasy is able to retrieve the time via WiFi connection. This possibility can be set up very easily and is described for example here: ESPEasy - NTP time retrieval [...]
Weiterlesen
HowTo: PCB - Build ButtonBoard PCB V1.2
The ButtonBoard PCB is my attempt to kill several birds with one stone. On the one hand I was always looking for a universal and easy to program remote control [...]
Weiterlesen
HowTo: PCB - pxlBlck_multiPCB
One of my past PCB projects is the "pxlBlck_multiPCB". As the name suggests this PCB is the heart of several future pxlBlck variants. So far I have used as main MCU for many projects the [...]
Weiterlesen
HowTo: 3D Printing - Building a Y-distributor for a 125mm exhaust hose
While setting up the exhaust system for my soldering station and the chamber of my 3D printer, I was faced with the problem of somehow splitting the intake of the exhaust system into two ways [...]
Weiterlesen
HowTo: ESPEasy - ESPEasy - Set up access password, backup and restore configurations
I am not sure if ESPs can really be misused to build a botnet. Either way, security should not be neglected even with the small ESPEasy devices. [...]
Weiterlesen
HowTo: Node Red - Trigger actions via Windows shortcut / mouse click
So that I can switch off my 3D printer automatically after the printing process, I have installed a Sonoff relay so that it can interrupt the power supply to the complete 3D printer. The relay [...]
Weiterlesen
HowTo: ESPEasy - Connecting the VL53L0X / VL53L1X distance sensor to the ESP8266 / ESP32 and reading it out
The VL53L0x or its sister/brother, the VL53L1X is a very accurate and relatively inexpensive laser distance sensor. With this, distances can be measured almost to the millimeter. In one of my [...]
Weiterlesen
HowTo: ESPEasy - Connecting BME280 / BMP280 to the ESP8266 and reading it out
The BME280 is one of the sensors I use in almost all my projects. With this not only the temperature can be measured. Also the humidity and the air pressure [...]
Weiterlesen
HowTo: ESPEasy - Configure MQTT Server and Subscribe to Topics
ESPEasy can now read out very many different sensors and / or control actuators (see also ESPEasy - Sensors & Actuators). With the help of the "Rules" can then locally on the ESP [...]
Weiterlesen
HowTo: ESPEasy – connect the rotary encoder to the ESP8266 and evaluate it
Especially if your own circuit has a display to show values, the next step is to also connect a control option. You can connect pushbuttons or switches. A [...]
Weiterlesen
English 
Deutsch 
Français 
Español 
Nederlands