I am currently working on a project that unfortunately exceeds the capabilities of my 3D printer. So far I was able to print all the necessary components on my 3D […]
Read more
Category: Evening project(<2h)
This category includes all projects of Nerdiy.de which require a maximum of two hours for the implementation or construction.
HowTo: ESPEasy – Connect the APDS-9960 gesture sensor to the ESP8266 / ESP32 and read its values
The APDS-9960 is a sensor that can be connected to a microcontroller such as the ESP8266 via the I2C bus. With the help of the sensor it is possible to […]
Read more
HowTo: 3D printing – Build a Y-distributor for a 125mm exhaust hose
While setting up the suction system for my soldering station and the chamber of my 3D printer, I was faced with the problem that I had to somehow split the […]
Read more
HowTo: ESPEasy – Set up password protection, save and restore configurations
I am not sure whether ESPs can really be abused to set up a botnet. Either way, you shouldn’t neglect the issue of security, even with the small ESPEasy devices. […]
Read more
HowTo: Node Red – Switch the Raspberry Pi screen on and off
So that my MagicMirror is only switched on when I actually use it, I have configured a small automation using NodeRed. The screen is only switched on if movement is […]
Read more
HowTo: 3D printing – Build a solder fume extraction hose incl. funnel
I also needed a suitable hose system to build my solder fume extraction system. After a little trial and error, I decided to use the standard exhaust air hoses. These […]
Read more
HowTo: Node Red – Trigger actions via Windows shortcut / mouse click
So that I can switch off my 3D printer automatically after the printing process, I installed a Sonoff relay so that it can interrupt the power supply to the entire […]
Read more
HowTo: ESPEasy – Connect VL53L0X / VL53L1X distance sensor to the ESP8266 / ESP32 and read its data
The VL53L0x or its sister / brother, the VL53L1X is a very precise and relatively inexpensive laser distance sensor. With this, distances can be measured almost at millimeter-accuracy. In one […]
Read more
HowTo: ESPEasy – Connect the BME280 / BMP280 to the ESP8266 and read its data
The BME280 is one of the sensors that I use in almost all of my projects. With this sensor one can not only measure the temperature. The air humidity and […]
Read more
HowTo: ESPEasy – Configure MQTT server on the ESP8266 and subscribe to topics
ESPEasy can read out a large number of different sensors and / or control actuators (see also ESPEasy – Sensors & Actuators). With the help of the “Rules” it is […]
Read more
HowTo: ESPEasy – Connect a rotary encoder to the ESP8266 and evaluate it
Especially if your own circuit has a display to show values, the next step is often to connect an interface option. You can connect buttons or switches. A relatively cool […]
Read more
HowTo: ESPEasy – Connect the PCA9685 PWM port extension to the ESP8266
The PCA9685 is quite a practical IC. This is connected to the microcontroller (e.g. ESP8266) via I2C and can then control up to 16 individual PWM channels. You can control […]
Read more
HowTo: Node Red – Control Spotify via NodeRed
What I really appreciate about Spotify is the good connectivity. You can play or control music or podcasts on another device with just a few clicks. Thanks to the free […]
Read more
HowTo: Node Red – Display close by gas station prices on the dashboard
Mit NodeRed bzw. den passenden Nodes könnt Ihr sehr leicht Daten aus dem Internet abrufen und aufbereitet anzeigen lassen. Ein praktischer Anwendungsfall dafür ist zum Beispiel der Abruf von Tankstellenpreisen […]
Read more
HowTo: Arduino – Build your own arduino timer “time_timy” to visualize a time period
The 3D printed housing of the “pxlDigits” was initially not intended to be “just” a 7-segment display with WiFi. Originally I used it to build a kind of timer from […]
Read more
HowTo: ESPEasy – Connect an LDR to the ESP8266 and read its value
There are some situations in which connecting an LDR to an ESP makes sense. In this way, the brightness in a room can be measured relatively easily and for little […]
Read more
HowTo: pxlBlck – Display relative values as a BarGraph
I started with the documentation of the pxlBlcks (which I had been postponed for a too long time) in November 2020 after Hackaday.com had announced the “GoodBye 2020” challenge. (More […]
Read more
HowTo: 3D printing – Build a foot tambourine yourself
Actually not one of the typical articles for Nerdiy.de, but recently I was looking for a tambourine that I could operate myself while playing the guitar. Long story short: Everything […]
Read more
HowTo: 3D printing – Build a foot rattle yourself
When looking for a foot rattle to accompany guitar playing, I had the same problem as with the foot tambourine. So again: do it yourself. 🙂 Instructions for building your […]
Read more
HowTo: pxlBlck – Build your own pxlBlck_RingClock
The pxlBlck_RingClock is very similar to the pxlBlck_SlotClock. It is also built using a 1 × 60 LED matrix and can display the time according to the same scheme as […]
Read more
HowTo: pxlBlck – Build your own pxlBlck_8x8
The pxlBlck_8x8 was one of the first members of the pxlBlck family. Thanks to the few parts and the prefabricated WS2812 8×8 LED matrix, it is set up fairly quickly […]
Read more
HowTo: pxlBlck – Design icons, transfer them to the pxlBlck and display them
I started developing the pxlBlcks because I was looking for a way to stay informed about events in the SmartHome. There are now two options integrated into the pxlBlck plug-in. […]
Read more
HowTo: pxlBlck – Configure and display animations
With the pxlBlck you can be informed about events in different ways. One of these possibilities is to be able to display previously set icons. Unfortunately, this option only works […]
Read more
HowTo: pxlBlck – Configure watch faces and screensavers
The adjustable dials differ from the type of LED matrix used. Unfortunately, this is the case because different LED-matrix sizes allow or do not allow different dials and screensavers. In […]
Read more
HowTo: pxlBlck – Automatic setting of the display brightness via LDR
If you not only want to stay informed about events with your pxlBlck and also use it to display the current time, then it might be you noticed that a […]
Read more
HowTo: ESPEasy – Activate NTP time retrieval from the Internet
Thanks to WiFi and thus (often) an internet connection, an ESP8266 or ESP32 programmed with ESPEasy also has the option to retrieve the actual time. In order for this to […]
Read more
HowTo: Electronics – Build waterproof 12V fairy lights yourself
For a camping trip I was looking for a cheap and bright fairy light. This should be waterproof and bright enough to illuminate the tent properly. It would be perfect […]
Read more
HowTo: Electronics – Encapsulate electronics waterproof with epoxy
During the construction of a chain of lights, I was faced with the problem of how to get this chain of lights waterproof. Ultimately, I built the electronic components, which […]
Read more
HowTo: Node Red – Fridge door monitoring by fridge energy consumption
In the past few weeks I’ve had the problem that my freezer door didn’t close properly. As a result, at least one night, the refrigerator door was not properly closed […]
Read more
HowTo: ESPEasy – Use a PCA9685 and ESPEasy to control servos
The PCA9685 is a PWM port expander. This makes it possible to connect up to 16 LEDs, servos or other components to your ESP8266 and supply them with a PWM […]
Read more